Ethylene oxide sterilizer manufacturer

EO sterilizer.Made In China

Sterilizer instructions
Contact us

Mail: jacky@hnbocon.com

Contacts: Jacky Jiang

Whatsapp/WeChat:

0086 18258800889

FAX: 0086 371 55951125

ADD: 51 Xiasha 22nd Street, Hangzhou, China

  • Specification configuration of ethylene oxide sterili
  • Maintenance of sterilizer
  • parametric release of sterilization
  • dry heat sterilization
  • The characteristics of the eo sterilizer
  • Touch operation of the eo sterilizer
  • Sterilizer instructions

    Time rate of pressure change

    by: EtO sterilizer manufacturerview: 1288 time: 2020-10-29
    In practical applications, the rate can be determined as the time (with tolerance) required to achieve a specified pressure change.
     
    a) The minimum temperature at which the product enters the sterilization process and / or the specified conditions required to reach the minimum required temperature;
     
    b) Pretreatment (if used)
    • 1) Time in the chamber / area, temperature and humidity of the chamber / area;
    • 2) Temperature and humidity of sterilization load;
    • 3) The longest running time from the removal of the load from the pretreatment to the start of the sterilization cycle;
     
    c) Vacuum degree and emptying rate (if used)
     
    Holding time under vacuum, if used;
    Note: the evacuation rate is usually defined as the minimum allowable evacuation time, the maximum allowable evacuation time or the acceptable evacuation time range, rather than the specific time of each operation.
     
     
    d) Inert gas flushing (if used)
    • 1) The pressure associated with the inert gas / steam (Δ P or terminal pressure) and the rate at which the pressure is reached (Δ P / time);
    • 2) The depth (Δ P or terminal pressure) and rate (Δ P / time) of reaching vacuum;
    • 3) Any number of repetitions and repetitions;
     
    e) Conditioning and / or humidity retention phase (if used)
    • 1) Pressure level and / or rate of reaching vacuum or relative humidity level, as controlled and monitored;
    • 2) Steam pulse number / vacuum degree (if used);
    • 3) Time;
    • 4) Test chamber temperature;
    • 5) Temperature and humidity of sterilization load at the end of treatment;

    f) EO injection and exposure:
    • 1) The injection pressure rise (Δ P), injection time and terminal pressure of EO injection phase were analyzed;
    • 2) Evidence that the gas EO has entered the sterilization chamber through pressure rise and any of the following ways;
      • i) Mass of ethylene oxide used (see d.10.2 I);
      • II) direct measurement of EO concentration;
      • III) ethylene oxide dosage.
    • 3) Sterilization room temperature;
    • 4) Exposure time;
    • 5) Sterilization load temperature;
    • 6) Indication of good operation of the chamber gas circulation system (if used) during exposure;
     
     
    g) After washing (e.g. after exposure)
    • 1) The depth (Δ P or terminal pressure) and rate (Δ P / time) of reaching vacuum;
    • 2) The pressure (Δ P or terminal pressure) associated with the inert gas / air / steam and the rate at which the pressure is reached (Δ P / time);
    • 3) Any change in the number of repetitions and successive repetitions;
     
    h) Aeration, if used:
    • 1) Time and temperature in the test chamber and / or indoor;
    • 2) Chamber and / or chamber pressure changes, if any;
    • 3) The rate of change of air or other gases;
    • 4) Temperature of sterilization load.

     
    Classification:Sterilizer instructions
    Recommended
    Recommended products